Technical article library

Metal Injection Molding Design Guidelines: Walls, Holes, Gates and Tolerances

Updated 3 November 2026 · CSMFG technical guides

Designing for metal injection molding means designing for four states: mold filling, ejection, binder removal and sintering. A shape that fills the mold can still crack during debinding or sag in the furnace, so the best design review follows the part through every stage.

The European Powder Metallurgy Association’s MIM design guidance recommends attention to wall uniformity because abrupt thickness differences can contribute to distortion and uneven shrinkage. The practical goal is a consistent, supportable part, not a universal wall-thickness number.

Watch: MIM Design Guidelines

Video and full transcript

How should wall thickness be designed?

MIM Design Guidelines: Design for filling, ejection, binder removal and sintering support
Design for filling, ejection, binder removal and sintering support. Open full-size infographic.

Keep sections as uniform as the function permits. Core out a heavy boss or add a gradual transition between a thick body and a thin arm. This can reduce material and help binder escape more consistently. Too-thin features create a different risk: feedstock may not fill them reliably, and fragile green or debound features can be damaged.

For example, a solid hub on a thin latch can be changed to a cored hub if the remaining wall carries the load. Check the core pin’s support, the allowable bore shape and whether secondary machining is required. Confirm the final design with mold-fill, handling and sintering reviews.

Where should holes, undercuts and threads go?

A through-hole that can be formed with a well-supported core is often easier than a deep blind feature. A side hole or undercut may need a moving slide or a post-sinter operation. Slides can be worthwhile when they eliminate repeated machining, but they increase tool complexity and maintenance.

Small threads may be molded in some cases, but a tapped thread can be preferable when thread quality is critical. Identify the mating part, thread class, loading and gauge method. A feature shown in CAD is not automatically economical to mold.

Thin arms and curved features illustrate the importance of section transitions and support during processing.
Thin arms and curved features illustrate the importance of section transitions and support during processing.

Why do gate and parting-line locations matter?

Gate and parting-line locations affect how a MIM tool fills and where the finished part may show a witness mark. The gate introduces powder-binder feedstock; separate flow fronts can meet at a knit line, while mold surfaces meet at the parting line. For example, a line on a noncritical clearance surface may be acceptable, whereas a line across a sealing face or loaded root needs closer assessment.

Review flow, venting, gate removal and ejection with the supplier. Mark appearance, sealing and fatigue-critical surfaces before the tool layout is approved.

Weld lines form where flow fronts meet, often around holes or obstructions. If the meeting point falls at a highly stressed section, the team should review the gate and validate the actual part. The visible surface alone may not reveal the whole risk.

How do shrinkage and furnace support affect tolerances?

The green part is deliberately larger than the finished part. Sintering shrinkage varies with feedstock and processing, and is not always perfectly uniform. A broad cantilever may sag without support; friction against a setter can also influence movement. Plan the furnace orientation and support surfaces before finalizing a critical datum scheme.

Avoid assigning the same tight tolerance to every dimension. Mark fit, sealing and positional features, and allow wider tolerances on nonfunctional surfaces. Obtain a tolerance proposal for each feature and specify where machining or sizing is permitted. Do not infer production capability from an isolated nominal percentage.

Examples of holes, contours and thin features that require a feature-specific design review.
Examples of holes, contours and thin features that require a feature-specific design review.

What belongs in a design review?

A MIM design review is a check of the component through filling, ejection, debinding, sintering and final inspection. The design must work in every state, including the fragile stages before the finished metal condition is reached. A shape that can be modeled in CAD is not automatically economical to mold, support and inspect.

For example, CSMFG's Cam Lever is specified in 17-4PH H900, and the supplied detail calls for a 2.30 ±0.03 drilled diameter. First identify the lever's assembly datums, contact faces and loaded pivot region. Then agree gates, core support, ejection, setter contact and any stock for secondary machining. Review the actual order quantity with the tool layout; the November 2026 Cam Lever price example applies above 2,000 pieces. The MIMA design guidance connects shape complexity with material performance and economics. Use the drawing review to turn those broad criteria into a specific manufacturing and inspection plan.

How should ribs, bosses and transitions be handled?

A rib or cored boss is a way to distribute material while preserving the component's function. Uniform, gradual section changes are usually easier to fill, debind and support than an abrupt junction between a heavy boss and a thin arm. The load path must still be maintained; removing material solely to reduce mass can create a weak section.

The CSMFG Cam Lever drawing provides a useful review geometry: a pivot region joins a longer contoured arm, with several specified profile radii. First inspect the transition for filling and green-part handling. Second decide how the arm and boss rest during sintering without damaging a functional face. The 17-4PH H900 final condition does not remove a geometric stress concentration or provide support during the earlier stages. For example, a cored hub may save feedstock but introduce a slender core pin and a new bore requirement. Compare the revised load path, tool practicality and final inspection before approving the design.

Can multiple components become one MIM part?

Sometimes. Combining a latch body and a cam can remove a pin, assembly step and tolerance stack. The resulting mold may need additional slides, and the combined part may be harder to support in the furnace. List the removed operations and new tooling or quality risks, then test the functional assembly. Integration is a design opportunity, not an automatic cost reduction.

Where a surface must be machined after sintering, identify stock allowance and a stable holding datum early. The sintering setter should not damage the eventual sealing or sliding surface.

What does the Cam Lever drawing teach about secondary features?

The CSMFG Cam Lever drawing is a useful example of separating a molded profile from a specifically called-out machined feature. The supplied detail marks DRILL: diameter 2.30 ±0.03, together with a diameter 2.80 × 90° countersink. The component is specified in 17-4PH H900. The cropped drawing does not include the complete title block, so the released drawing must govern units, datums and general tolerances.

First review the lever contour, wall transitions and support through debinding and sintering. Then identify the drilled feature, its datum relationship and the final inspection condition. A drill callout is a design requirement; it does not prove that the diameter is held as molded. According to CSMFG's November 2026 part example, the lever's reference price is RMB 2.40 per piece above 2,000 pieces. See the cost case for the associated production photo and price scope.

CSMFG Cam Lever drawing detail: drilled diameter 2.30 ±0.03 and a diameter 2.80 × 90° countersink callout.
CSMFG Cam Lever drawing detail: drilled diameter 2.30 ±0.03 and a diameter 2.80 × 90° countersink callout.

How should a powder-metal thread be reviewed?

A thread is a functional feature whose route should be agreed before the powder-metal tool is made. The CSMFG Holder / Halter drawing marks M6 in two positions and shows both faces of the component. The associated conventional-PM specification is SS304L, 6.6 g/cm³ and 45 HRB. The supplied product photograph shows the matching repeated part geometry, providing a practical basis for discussing tool access and inspection.

For example, identify whether each thread will be formed or tapped, how the part will be held, and how burrs and cleaning will be controlled. The drawing's thread callout alone does not settle that manufacturing choice. A threaded holder and a pivoting MIM lever need different feature plans even when both are small stainless parts. Review the secondary-operation options with the complete drawing and mating requirements, then retain the final route with the quote.

CSMFG Holder / Halter drawing, with two M6 thread callouts and the supplied profile dimensions.
CSMFG Holder / Halter drawing, with two M6 thread callouts and the supplied profile dimensions.

MIM design questions

Can MIM create undercuts and side holes?

An undercut or side hole is a feature that can require moving tooling, a removable core or a secondary operation in MIM. A mold slide may form a feature across the opening direction, but adds investment, wear and maintenance. Drilling after sintering can instead keep the mold simpler while adding repeated handling and inspection.

For example, the CSMFG Cam Lever detail explicitly calls for a drilled pivot feature with a 2.30 ±0.03 diameter requirement. That callout should be priced and inspected as a manufacturing feature, rather than treated as proof of an as-molded hole capability. First identify the feature direction and access. Then compare tool complexity with the recurring cost of machining, deburring and gauging. According to MIMA's secondary-operation guidance, machining can add features that are costly or difficult to include in tooling. The November 2026 CSMFG examples show why the complete route matters more than a claim that every feature can be molded.

Should every MIM dimension have a tight tolerance?

A MIM drawing should apply tight tolerances to features that control fit, function or safety, rather than to every dimension by default. A bore diameter and its position relative to a contact face may determine whether a latch assembles; the outside profile may only need clearance. Specify the datum scheme and whether inspection occurs before or after coating or machining.

Ask for a feature-specific capability review across cavities and representative furnace loads. For example, selected machining may control the bore economically while leaving noncritical contours as sintered. A single percentage does not describe every source of dimensional variation.

Related reading: Learn the MIM process, troubleshoot MIM defects, and plan MIM tolerances and shrinkage.

Request a drawing review through CSMFG’s powder metallurgy and MIM services.

Allow for post-sinter machining and finishing when defining tool access and critical surfaces.